How To Power Cycle Wyze Camera? (What You Should Know)

In general, power cycling a Wyze camera can usually fix the majority of issues; this method is relatively easy to use and usually succeeds in getting Wyze devices working again.

You should power cycle for a number of reasons. One possibility is that the camera is unaware of your commands. Another possibility is that the camera is unable to connect to your Wi-Fi network or that the image quality is subpar. An occasional power cycle may also solve issues with motion detection or alarms.

You might need to quickly reboot your Wyze Cam Outdoor if you have one. Here is how to power cycle it using it.

How to Power Cycle Wyze Camera?

Disconnecting the device from all power sources is typically how you power cycle, or completely turn off an electronic device.

By using this troubleshooting method, you can reset the device and its connections without having to go through burdensome formal processes.

Use power cycling to address a variety of troubleshooting problems. To do so, follow these steps:

1. Remove the plug from the Wyze device’s power supply. Both approaches—from the switchboard side or the camera side—are effective.
2. Allow the camera to completely discharge itself by giving it at least 10-15 seconds.
3. Reconnect the device to the power source and give it time to restart.

How Do You Power Cycle a Wyze Cam V2?

Similar to power cycling any other Wyze camera, the Wyze Cam V2 is no exception. However, you will need to Hard Reset it if you have repeatedly power cycled it and are still unable to connect to your WYZE Cam V2.

How to Power Cycle Wyze Outdoor Camera?

Simply follow this procedure:

1. Take your Wyze outdoor camera off the hook and unplug it.
2. Once the batteries have been removed, wait at least two minutes before replacing them.
3. Repeat the process and give it another 15 seconds before turning it on.
4. It ought to be performed expertly.

How to Power Cycle Wyze Camera Remotely?

To remotely power cycle your Wyze camera:

1. Choose your Wyze camera from the list on the Wyze App by going there.
2. Power it OFF.
3. In case it can be controlled remotely, turn off the main switch.) If not, you can skip this additional warning.
4. Restart it after at least 15 minutes have passed.
5. The expected reset should occur.

Nevertheless, if the camera becomes completely frozen, a remote restart will never be successful.

How to Get the Wyze Camera Back Online?

There are a few troubleshooting procedures you can follow if your Wyze Cam Outdoor isn’t connecting.

Step 1: By unplugging your Wyze Base station for 30 seconds, you can restart it.

Step 2: Verify the Wyze Cam Outdoor and Base Station status lights. If one is flashing while the other is solid blue, they are still attempting to connect.

Step 3: Tap on the paired Base Station after launching the Wyze app. Consider moving your base station closer if there is only one bar of signal strength.

Step 4: For four hours, charge the Wyze Camera Outdoor. When necessary, you can check battery levels using the mobile app.

Step 5: Go to Account > Firmware > Upgrade in the Wyze app, then tap Update. Communication between the devices can be ensured by using the appropriate software.

What Can You Do If the Camera Doesn’t Connect Even After the Power Cycle of the Device?

1. You must first reboot your Wyze Base station by cutting the power to it for 30 seconds.
2. The Wyze Cam Outdoor and Base Station status lights must then be checked. If either of them is flashing, they are still attempting to connect even though they should both be solid blue.
3. Just launch the Wyze app after that and choose the connected Base Station to proceed. Simply move your base station closer if there is only one bar of signal strength.
4. You must now spend four hours outside charging the Wyze Camera. Anytime you need to, you can check the battery level using the mobile app.
5. Open the Wyze app on your iOS or Android device, go to Account > Firmware > Upgrade, and then click Update. The precise software can secure communication between the devices.

Why is My Wyze Camera Not Connecting?

It might be the Wi-Fi frequency if there is a connection issue and there are frequent time-outs during setup. Most Wi-Fi routers available today support both 2.4GHz and 5GHz. So you had better make sure you were on the 2.4GHz Wi-Fi network.

Wyze Error Code 90 can also be brought on by slow internet or connections that are more restrictive than usual.

Verify that no significant device is blocking the Wyze camera’s access to signals; otherwise, an error may be paved.

Unplugging the wires, sockets, etc. can be used to fix corrosion and everyday issues. and plugging them back in. In most cases, these annoying problems are simple to resolve using simple techniques.

The least amount of bandwidth needed by the Wyze Cam can end up being overused if Wi-Fi channels become oversaturated, which frequently results in the Wyze Error Code 90.

SD Card may also be to blame! Wyze Error Code 90 is likely to appear if the installed SD card is corrupt. Reason: SD Card corruption prevents the camera’s live streaming from being processed properly in the back. It occasionally brings it to a complete stop.


You might want to install a smart switch between the camera power adapter and the socket to address this problem. Not more than $10, please. The problem will nevertheless continue if the nearby Wi-Fi signals are insufficient or weak. The Connectivity-Troubleshooting option will be the final resort.

Leave a Reply

Your email address will not be published.

Previous post How To Remove A Person From A Photo On iPhone? Four Methods
Why Does Photo Booth Freeze When I Record? How To Fix? Next post Why Does Photo Booth Freeze When I Record? How To Fix?